Style Arc Estelle Ponte Jacket

This is a fabulous jacket that I have been itching to make for a while now. Megan and Sue have both recently made this jacket and after a long wait the pattern finally arrived from Style Arc and I couldn't wait to get started. (This delay seems to be an Australia Post issue.)

As described on the Style Arc website "This fabulous jacket is not just easy to wear but it is very easy to make. The knee length and the gorgeous waterfall collar makes this jacket a great trans seasonal addition to your wardrobe. A project you can complete in an afternoon."

Style Arc Estelle Ponte Jacket

I had this gorgeous indigo renewal wool ponte purchased from Knitwit with intentions of making some sort of warm jacket. I work in a chilly office and I am determined to make some warmer things to keep me from freezing this winter. At $49.95 a metre I was nervous of making a wadder, but after doing lots of research and knowing that Style Arc patterns generally fit my body shape quite well, and that this was a loose fit style, I went ahead and cut a size 12.

And I am very happy with the result. These photos were taken in a rush this morning just before I left for work. I am wearing it with a Colette Mabel Skirt and a Deer and Doe Plantain Tee. I can see it working with lots of other things in my wardrobe too, and after wearing it today I am happy to say it was warm and comfortable...just what I needed.

This is a photo I posted on IG on Saturday night, with all the edges left raw. The general consensus was to leave the edges raw, which both Megan and Sue have done. I left it overnight but Sunday morning I decided to finish off those raw edges. It just didn't look right or feel right to me, left like this. Even though I had used a rotary cutter and the edges were quite neat, they were not perfect.

The instructions say to sew the seams as "flat seams". This means sew the seam, then trim away the left seam allowance, then turn the right seam allowance over the cut away left seam and stitch the seam allowance down. This creates a nice flat seam, similar to a flat felled seam, without tucking the raw edge under. Can you spot the huge mistake I made in the photo above? Yes, I sewed the back collar seam inside out so that the raw edge is visible when the collar is folded down. I was too far into the construction before I realised my error...but I think I can live with it.

I deliberated long and hard about how to finish off the raw edges. The ponte is quite bulky and I could see it would be difficult to do a neat job of turning a 1cm hem twice and stitching. I quite like the look of the flat seams on the inside so I embraced this look and simply turned a 12mm hem in a single fold and stitched very close to the raw edge. Although this is quite a simple technique, it took me ages to accurately measure, press and pin the entire edge of this jacket. I knew this finish would only work if it was done very neatly and I am very happy with the result.

With the waterfall front on this jacket the wrong side shows below the turn of the lapels. If I continued to turn the hem the same way around the bottom edge of the jacket, the wrong side would be showing, so I decided to switch directions at the bottom front corners. You can see this corner in the photo above. I trimmed a square from the corner to remove some bulk and I used some Vliesofix-bondaweb-tape to help hold them securely. This resulted in a nice neat corner.

I finished the sleeve hems exactly the same way, which meant I didn't lose too much length, and they visually match the rest of the jacket.

Above is a shot of the inside showing the flat seams at the shoulder and armhole and also the wrong side of the lapel edge finish.

And another inside shot showing the in seam pocket. I finished off the side seams with the overlocker because it was late and I was getting tired and I couldn't think how to do flat seams with the pockets.

This jacket took me much longer than an afternoon to construct, but if you leave the edges raw it is an easy and quick sew. I am so glad I spent the extra time finishing the edges...to me it was well worth it.

Happy Sewing